Home & Kitchen

Pentek EPM-10 Carbon Block Filter Cartridge, 9-3/4″ x 2-7/8″, 10 Microns

#ad
#ad
Pentair Industries EPM-10 #ad - Nominal filtration rating of 10 microns. For most residential, commercial, and industrial applications, water filters are manufactured in the form of replaceable cartridges that fit inside permanent housings. The performance of filters is measured by the minimum particle size that is blocked, the percentage of particles or microorganisms that are removed, the downstream concentration of unwanted chemicals, the maximum flow rate, and the amount of water that can be filtered before the filter must be replaced.

The company, founded in 1966 and headquartered in Minneapolis, MN, meets International Organization for Standardization ISO standards 9001 and 14001 for quality assurance. Reduces fine sediment and chlorine taste and odor in residential and commercial drinking water. The filter will reduce free available chlorine FAC at 2 parts per million ppm by at least 90% in up to 3, 000 gallons at a flow rate of 1 gallon per minute gpm.

Chlorine reduction capacity is the minimum total amount of water for which the free available chlorine FAC at a concentration of 2 ppm is reduced by at least 90%. H is height, the horizontal distance from left to right; D is depth, the vertical distance from lowest to highest point; W is width, the horizontal distance from front to back.

Pentek EPM-10 Carbon Block Filter Cartridge, 9-3/4" x 2-7/8", 10 Microns #ad - Water filters remove undesirable particles, adsorption, chemicals, and microorganisms from water by means of a semipermeable barrier, or biological processes. They are made of densely packed synthetic or natural fibers that trap suspended particles, or substances that cause a chemical change, materials that block microbes or adsorb unwanted chemicals, such as acid neutralization.

This cartridge is made of bonded powdered activated carbon PAC filter media wrapped in polyolefin with polyethylene outer netting.

More information about Pentair Industries EPM-10 #ad

Pentek EP-10 Carbon Block Filter Cartridge, 9-3/4" x 2-7/8", 5 Microns

#ad
#ad
Pentair Industries 1/2" 3G Slim Line BSP #ad - This cartridge is made of bonded powdered activated carbon PAC filter media wrapped in a polyolefin pre-filter with polyethylene outer netting. Bonded pac media with polyolefin pre-filter and polyethylene netting for extended life. The performance of filters is measured by the minimum particle size that is blocked, the downstream concentration of unwanted chemicals, the maximum flow rate, the percentage of particles or microorganisms that are removed, and the amount of water that can be filtered before the filter must be replaced.

The filter will reduce free available chlorine FAC at 2 parts per million ppm by at least 90% in up to 6, 000 gallons at a flow rate of 1 gallon per minute gpm. This pentek ep-10 carbon block filter cartridge reduces fine sediment and chlorine taste and odor in residential and commercial drinking water.

Pentek EP-10 Carbon Block Filter Cartridge, 9-3/4" x 2-7/8", 5 Microns #ad - Reduces fine sediment and chlorine taste and odor in residential and commercial drinking water. The cartridge has an initial pressure drop of 3. 4 pounds per square inch psi at a flow rate of 1 gallon per minute gpm, and operates over a temperature range of 40 to 180 degrees F 4. 4 to 82. 2 degrees C. It has a nominal 85% filtration rating of 5 microns.

Nominal filtration rating of 5 microns.

More information about Pentair Industries 1/2" 3G Slim Line BSP #ad


Similar products



Pentek CBC-10 Carbon Block Filter Cartridge, 9-3/4" x 2-7/8", 0.5 Micron

#ad
#ad
Pentair Industries CBC-10 #ad - For most residential, commercial, and industrial applications, water filters are manufactured in the form of replaceable cartridges that fit inside permanent housings. Reduces fine sediment, chlorine taste and odor, and protozoan cysts in residential and commercial drinking water. Chlorine reduction capacity is the minimum total amount of water for which the free available chlorine FAC at a concentration of 2 ppm is reduced by at least 90%.

H is height, the vertical distance from lowest to highest point; W is width, the horizontal distance from left to right; D is depth, the horizontal distance from front to back. Water filters remove undesirable particles, adsorption, and microorganisms from water by means of a semipermeable barrier, chemicals, or biological processes.

Pentek CBC-10 Carbon Block Filter Cartridge, 9-3/4" x 2-7/8", 0.5 Micron #ad - This pentek cbc-10 carbon filter cartridge reduces fine sediment, chlorine taste and odor, and protozoan cysts in residential and commercial drinking water. The nitrile butadiene rubber Buna-N gaskets seal the cartridge against the housing sold separately. Nominal filtration rating of 5 microns. This carbon block filter cartridge meets national Sanitation Foundation/American National Standards Institute NSF/ANSI standard 42 for quality assurance, and is for purification of residential and commercial drinking water.

SpecificationsNominal filtration rating05 microninitial pressure drop at 2 gpm3. 7 psiremoval of protozoan cysts99.

More information about Pentair Industries CBC-10 #ad


Similar products



Pentek WS-10 Water Softener 10”Cartridge, 155319-43

#ad
#ad
Pentek WS-10 #ad - Nominal filtration rating of 05 micron. Capacity of 750 grains. Initial pressure drop of 3. 7 psi at a flow rate of 2 gpm. The performance of filters is measured by the minimum particle size that is blocked, the maximum flow rate, the percentage of particles or microorganisms that are removed, the downstream concentration of unwanted chemicals, and the amount of water that can be filtered before the filter must be replaced.

Reduces fine sediment, chlorine taste and odor, and protozoan cysts in residential and commercial drinking water. This pentek ws-10 water softening filter cartridge reduces hardness minerals and scale deposits in low flow rate residential and commercial applications. Reduces fine sediment and chlorine taste and odor in residential and commercial drinking water.

Pentek WS-10 Water Softener 10”Cartridge, 155319-43 #ad - The cartridge has a capacity of 750 grains, a recommended flow rate of 050 gallons per minute gpm, and a maximum operating temperature of 100 degrees F 37. 8 degrees C. This water softening filter cartridge is used for treatment of residential and commercial water. Specifications Capacity 750 grains Recommended flow rate 0

50 gpm maximum temperature 100 degrees F 37. 8 degrees c maximum dimensions h x w 9-3/4 x 2-5/8 inches 248 x 67 mmh is height, the horizontal distance from left to right; D is depth, the vertical distance from lowest to highest point; W is width, the horizontal distance from front to back.

More information about Pentek WS-10 #ad


Similar products



Desal DESAL-TFM-50 Reverse Osmosis Membrane

#ad
#ad
GE Osmonics DESAL-TFM-50 #ad - The tfm-50 is also known as 1204694, and ge desal 1229149, ge tfm50ak, ge tfm50nt, ge tfm-50NT, GE TFM-50AK, for easy reference. Reduces hardness minerals and scale deposits in low flow rate residential and commercial applications. The ge osmonics desal tfm-50 ro membrane has a flow rate of 50 gallons per day, an outstanding amount of drinking water for your average household.

Temperature range of 40 to 180 degrees F 4. 4 to 82. 2 degrees C. Reverse osmosis technology reduces lead, mercury, chromium, nitrates and many more contaminants. Cation, sodium-form resin ion-exchange media with polypropylene pre- and post-filters. Maximum temperature of 100 degrees F 37. 8 degrees C. Ansi/nsf 58 listed for performance.

Desal DESAL-TFM-50 Reverse Osmosis Membrane #ad - Initial pressure drop of 3. 4 psi at a flow rate of 1 gpm. 50 gallons per day--plenty of great RO water for your home. Impurities captured on the membrane are constantly swept away, so the surface is continuously cleaned--reducing maintenance costs. Nominal filtration rating of 5 microns.

More information about GE Osmonics DESAL-TFM-50 #ad


Similar products



Pentek PD-5-934 Polypropylene Filter Cartridge, 9-7/8" x 2-1/2", 5 Microns

#ad
#ad
Pentair Industries PD-1-934 #ad - This pentek pd-5-934 polypropylene filter cartridge reduces sand, scale, silt, and rust particles in commercial drinking water and industrial fluid applications. It has a nominal filtration rating of 5 microns at an efficiency of 85%. This polypropylene filter cartridge meets national Sanitation Foundation/American National Standards Institute NSF/ANSI standard 42 for quality assurance, and is used for treatment of commercial drinking water and industrial filtration applications.

SpecificationsNominal filtration rating5 micronsInitial pressure drop at 2 gpm. The filter is made of thermally bonded polypropylene microfibers for resistance to chemicals and bacteria and minimal fiber release. It has an initial pressure drop of less than 2 pounds per square inch psi at a flow rate of 2 gallons per minute gpm, and operates over a temperature range of 40 to 175 degrees F 4.

Pentek PD-5-934 Polypropylene Filter Cartridge, 9-7/8" x 2-1/2", 5 Microns #ad - 4 to 79. 4 degrees C.

More information about Pentair Industries PD-1-934 #ad


Similar products



Pentek PS5-10C Sediment Water Filters

#ad
#ad
Pentek PS5-10C #ad - Polypropylene spun bonded for high sediment retention. Standard size cartridge to fit Pentek housings and other manufacturers. Resistant to chemicals and corrosion. Reduces fine sediment, chlorine taste and odor, and protozoan cysts in residential and commercial drinking water. The pentek ps5-10c water filters reduce extra-fine dirt, sand, sediment, silt, rust particles and scale particles.

The pentek ps5-10c water filter is resistant to chemicals and corrosion. Initial pressure drop of less than 2 psi at a flow rate of 2 gpm. Pentek 5 micron sediment filter. Spun fibers form a true gradient density from outer to inner surfaces. Impurities captured on the membrane are constantly swept away, so the surface is continuously cleaned--reducing maintenance costs.

Pentek PS5-10C Sediment Water Filters #ad - Initial pressure drop of 3. 4 psi at a flow rate of 1 gpm. Reduces sand, silt, scale, and rust particles in commercial drinking water and industrial fluid applications. Nominal filtration rating of 5 microns. Fits in whole house water filter systems. Spun-bonded polypropylene sediment Water Filter Cartridge Reduces extra-fine dirt, silt, sand, sediment, rust particles and scale particles.

More information about Pentek PS5-10C #ad


Similar products



2 pk Pentek 155014-43, P5 9-3/4" x 2-3/8" 5 Micron Sediment Melt Blown Filters Cartridges Spun Polypropylene

#ad
#ad
Pentek P5 #ad - Reduces sand, scale, silt, and rust particles in commercial drinking water and industrial fluid applications. Nominal filtration rating of 5 microns. Recommended flow rate of 050 gpm. Ps5-10c 5 micron sediment filter. Temperature range of 40 to 175 degrees F 4. 4 to 79. 4 degrees C. Initial pressure drop of less than 2 psi at a flow rate of 2 gpm.

Specifications: Features: made from continuous spun, thermally bonded polypropylene fibers. This standard 10 inch replacement cartridge has exceptional filtration of solids while maintaining water flow rate >8 GAL per minute. Reduces fine sediment, chlorine taste and odor, and protozoan cysts in residential and commercial drinking water.

2 pk Pentek 155014-43, P5 9-3/4" x 2-3/8" 5 Micron Sediment Melt Blown Filters Cartridges Spun Polypropylene #ad - 10" whole house Sediment Filtration. Temperature range of 40 to 180 degrees F 4. 4 to 82. 2 degrees C. Temperature range of 40 to 180 degrees F 4. 4 to 82. 2 degrees C. Polypropylene spun bonded for high sediment retention.

More information about Pentek P5 #ad


Similar products



Pentek ChlorPlus 10 Carbon Block Filter Cartridge, 10" x 2-1/2", 1 Micron

#ad
#ad
Pentair Industries ChlorPlus-10 #ad - Bonded pac media with polyolefin wraps and polyethylene netting. Capacity of 750 grains. Impurities captured on the membrane are constantly swept away, so the surface is continuously cleaned--reducing maintenance costs. Nominal filtration rating of 05 micron. Bonded polypropylene microfiber for resistance to chemicals and bacteria.

The cartridge is made of bonded powdered activated carbon PAC media with a polyolefin core and shell and polyethylene outer netting. Greater dirt holding ability and longer life than non-layered cartridges. Meets fda requirements for food and beverage contact. Reduces fine sediment and chlorine taste and odor in residential and commercial drinking water.

Pentek ChlorPlus 10 Carbon Block Filter Cartridge, 10" x 2-1/2", 1 Micron #ad - Chlorine reduction capacity is the minimum total amount of water for which the free available chlorine FAC at a concentration of 2 ppm is reduced by at least 75%. Reduces fine sediment, chlorine taste and odor, and protozoan cysts in residential and commercial drinking water. They are made of densely packed synthetic or natural fibers that trap suspended particles, materials that block microbes or adsorb unwanted chemicals, or substances that cause a chemical change, such as acid neutralization.

Greater dirt holding ability and longer life than non-layered cartridges. Great for whole home, wells, Reverse Osmosis Pre-Stage or Stage One Filtration. Reduces hardness minerals and scale deposits in low flow rate residential and commercial applications.

More information about Pentair Industries ChlorPlus-10 #ad


Similar products



Tier1 Replacement for Pentek P5 GXWH04F P5-10 5 Micron 10 x 2.5 Spun Wound Polypropylene Sediment Water Filter

#ad
#ad
Tier1 #ad - The p5 pentek comparable whole house replacement Sediment Filter Cartridge by Tier1 is manufactured for use in housings that require 10 x 2. 5 inch filter cartridges. Maximum temperature of 100 degrees F 37. 8 degrees C. Ps5-10c 5 micron sediment filter. Quick & easy installation: Quick and easy installation into your 10 x 2.

5 inch standard filtration system. 6 month filter life: by replacing your water filter every 6 months, depending on your water quality, you keep your water tasting great with the Tier1 WC34-PR. Initial pressure drop of less than 2 psi at a flow rate of 2 gpm. Tier1 water filters confidently reduce virtually all impurities, 5 micron or larger, from your water.

Tier1 Replacement for Pentek P5 GXWH04F P5-10 5 Micron 10 x 2.5 Spun Wound Polypropylene Sediment Water Filter #ad - Bonded pac media with polyolefin wraps and polyethylene netting. Meets fda requirements for food and beverage contact. Temperature range of 40 to 125 degrees F 4. 4 to 51. 7 degrees C. Thin-film membrane, a standard in reverse osmosis technology. 2 pack of 5 micron 10" replacement sediment filters.

More information about Tier1 #ad


Similar products



Pentek P5 Spun Polypropylene Filter Cartridge, 9-3/4" x 2-3/8", 5 Microns

#ad
#ad
Pentair Industries P5 #ad - Nominal filtration rating of 5 microns. The company, founded in 1966 and headquartered in Minneapolis, MN, meets International Organization for Standardization ISO standards 9001 and 14001 for quality assurance. Ps5-10c 5 micron sediment filter. They are made of densely packed synthetic or natural fibers that trap suspended particles, materials that block microbes or adsorb unwanted chemicals, or substances that cause a chemical change, such as acid neutralization.

Initial pressure drop of 02 psi at a flow rate of 5 gpm. Recommended flow rate of 050 gpm. Ansi/nsf 58 listed for performance. Bonded pac media with a polyolefin core and shell. Reduces fine sediment, chlorine taste and odor, and protozoan cysts in residential and commercial drinking water. Maximum temperature of 100 degrees F 37.

Pentek P5 Spun Polypropylene Filter Cartridge, 9-3/4" x 2-3/8", 5 Microns #ad - 8 degrees C. The filter is made of spun polypropylene fibers for resistance to chemicals and bacteria. Pentek 5 micron sediment filter. Filtration systems typically consist of a series of two or more types of filters, each designed to remove different contaminants. Initial pressure drop of 3.

More information about Pentair Industries P5 #ad


Similar products


Pmelax is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com.